Autor: Cheng, F. - Prolib Integro

Skocz do pozycji: 1.

Tytuł:: Study of inorganic powders used for preparation of waterproof coating to coal mine roadways
Badanie proszków nieorganicznych stosowanych do przygotowania wodoodpornych powłok jezdni w kopalniach węgla
Autorzy:: Song, H.
Liu, J.
Xue, F.
Cheng, F.
Tematy:: waterproof coating
coal mine roadway
adhesive
inorganic filler
powłoka wodoodporna
jezdnia w kopalni węgla
spoiwo
napełniacz nieorganiczny; Pokaż więcej
Wydawca:: Sieć Badawcza Łukasiewicz - Instytut Chemii Przemysłowej
Powiązania:: https://bibliotekanauki.pl/articles/947175.pdf Link otwiera się w nowym oknie
Opis:: The new coatings based on styrene-acrylate copolymer with solid powder additives were prepared. Solid additives were one of three types of adhesives (white cement, Portland cement, and alumina cement) and one of four inorganic fillers (quartz powder, talcum powder, calcium carbonate powder, and fly ash). The coatings were tested by determination of surface drying time, hard drying time, tensile strength, and elongation at break. The ratio of water absorption after 7 days was also measured. The results showed that white cement was the best inorganic adhesive with optimal amount of 40–50 wt % in solid powder part. Quartz powder served as better inorganic filler compared with talcum powder and calcium carbonate powder. Fly ash could also be used as good inorganic filler but in amount lower than 10 wt %. Thus prepared coatings satisfy requirements for class III according to GB/T23445-2009 standard.
Przygotowano nowe powłoki na bazie kopolimeru styren-akrylan z dodatkiem proszków stałych. Dodatki stałe stanowiły jeden z trzech rodzajów spoiwa (cement biały, cement portlandzki i cement glinowy) oraz jeden z czterech napełniaczy nieorganicznych (kwarc w postaci proszku, talk, sproszkowany węglan wapnia oraz popiół lotny). Powłoki badano przez określanie czasu suszenia powierzchni, czasu całkowitego suszenia, wytrzymałości na rozciąganie i wydłużenia przy zerwaniu. Wyznaczano również współczynnik absorpcji wody po 7 dniach. Badania wykazały, że najlepszym spoiwem nieorganicznym jest cement biały wilości 40–50 % mas. Proszek kwarcowy jest lepszym napełniaczem nieorganicznym niż talk lub sproszkowany węglan wapnia. Stwierdzono również, że dobrym napełniaczem nieorganicznym są popioły lotne, ale mogą być stosowane tylko w ilości mniejszej niż 10 % mas. Tak przygotowane powłoki spełniają wymagania klasy III według normy GB/T 23445-2009.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 2.

Tytuł:: Flame retardant properties of gas sealing materials used in coal mines
Uniepalniacze w materiałach zabezpieczających ściany w kopalniach węgla przed wypływem gazu
Autorzy:: Song, H.
Liu, J.
Xue, F.
Cheng, F.
Tematy:: flame retardant
coal mine
gas sealing materials
tensile strength
flame resistance properties
opóźniacz palenia
kopalnia węgla
materiały zabezpieczające przed wypływem gazu
wytrzymałość na rozciąganie
odporność na płomień; Pokaż więcej
Wydawca:: Sieć Badawcza Łukasiewicz - Instytut Chemii Przemysłowej
Powiązania:: https://bibliotekanauki.pl/articles/947389.pdf Link otwiera się w nowym oknie
Opis:: Flame retardants are key ingredients for gas sealing materials used in the coal mine wall. In this paper, the types and doses of flame retardants are investigated. The results showed that a gas sealing material with 11 wt % complex flame retardants had a good performance when the complex flame retardants were composed of aluminum hydroxide and chlorinated paraffin at a ratio of 3:8. The flame resistant property of this gas sealing material conforms to the safety standards of coal mines (MT113-1995). Furthermore, their mechanical properties met the standard requirements of the polymer cement waterproof coatings (GB/T23445-2009). The costs are very low compared with similar products in current practical use.
Zbadano wpływ rodzaju oraz ilości uniepalniacza, dodanego do emulsji styrenowo-akrylowej napełnionej krzemionką i cementem, na palność otrzymanej kompozycji zabezpieczającej ściany w kopalni węgla przed wypływem gazu. Efekt opóźnienia palenia na poziomie przewidzianym w normach bezpieczeństwa kopalń węgla (MT113-1995) uzyskano w wypadku zastosowania materiału uszczelniającego, modyfikowanego dodatkiem 11 % mas. kompozycji uniepalniacza, stanowiącej mieszaninę wodorotlenku glinu i chlorowanej parafiny w stosunku masowym 3:8. Modyfikowane materiały uszczelniające spełniają również wymagania pod względem właściwości mechanicznych, dotyczące polimerowo-cementowych powłok wodochronnych (GB/T23445-2009), a koszt ich wytwarzania jest dużo niższy niż koszt wytwarzania stosowanych obecnie produktów.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 3.

Tytuł:: Effect of oxidation on the wetting of coal surfaces by water: experimental and molecular dynamics simulation studies
Autorzy:: Li, E.
Lu, Y.
Cheng, F.
Wang, X.
Miller, J. D.
Tematy:: wettability
oxidation
molecular dynamics simulation
hydrogen bonding
contact angles
coal surfaces; Pokaż więcej
Wydawca:: Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Powiązania:: https://bibliotekanauki.pl/articles/109792.pdf Link otwiera się w nowym oknie
Opis:: The wettability of coal surfaces by water continues to be one of the key factors which determines the success of coal flotation. Consequently, oxidation of coal surfaces is a fundamental issue of interest. In this work, the effect of oxidation on the wetting of coal surfaces and the interaction between water molecules and oxygen-containing sites at the coal surface was investigated based on advancing/receding contact angle measurements and molecular dynamics simulations. For the simulation studies, a flat coal surface was constructed with the assistance of the molecular repulsion between graphite surfaces and the assembly of Wiser coal molecules. Our results indicated that the simulated advancing and receding contact angles were very similar, and both of them decreased, as expected, with an increase of hydroxyl sites at the coal surface. The good agreement between the simulated advancing/receding contact angles and the experimental receding contact angle values suggested that the configuration of the systems and the set of parameters for the simulation were appropriate. The spreading of water is mainly due to the hydrogen bonds formed between the interfacial water molecules and the hydroxyl sites at the coal surface. The hydroxyl groups show stronger hydration capacity than other oxygen-containing groups according to the calculated hydrogen bonds and interaction energies.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 4.

Tytuł:: Transcriptomic analysis of different tissues in Korean arborvitae
Autorzy:: Mu, H.
Gao, Y.
Cheng, F.
Lin, L.
Wang, G.
Xia, F.
Tematy:: Thuja koraiensis
transcriptome
tissue specific; Pokaż więcej
Wydawca:: Polska Akademia Nauk. Instytut Dendrologii PAN
Powiązania:: https://bibliotekanauki.pl/articles/2077762.pdf Link otwiera się w nowym oknie
Opis:: Korean arborvitae (Thuja koraiensis) is an evergreen shrub or small tree native to Korea and the extreme Changbai Mountain of China threatened by habitat loss. Due to the limited genomic sources of Ko- rean arborvitae, it is important to explore transcriptome to understand this economically important plant. We used RNA-seq technology to characterize the transcriptome of root, stem and leaf in Korean arborvitae, respectively. Based on the bioinformatics analysis of assembled transcriptome data, transcriptional path- ways and differentially expressed genes (DEGs) were identified. There were 152.26 million reads generated, and 446,568 unigenes with a mean size of 423.51 nt obtained via de novo assembly. Of these, 204,091 unigenes (45.70%) were further annotated by comparison to public protein databases. A total of 63,495 unigenes (14.22%) were associated into 130 pathways by searching against the KEGG database. DEGs analysis identified 11,890, 5,900 and 10,136 DEGs from the comparison of root vs. stem, root vs. leaf and stem vs. leaf, respectively. Besides, photosynthesis, plant hormone signal transduction and metabolism and biosynthesis of sugar and amino acids were changed in different tissues. We obtained 446,568 unigenes in Korean arborvitae and 11,890, 5,900 and 10,136 DEGs from the compar- ison of root vs. stem, root vs. leaf and stem vs. leaf, respectively. These results will aid in understanding and carrying out future studies on the molecular basis of Korean arborvitae and contribute to future artificial production and applications.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 5.

Tytuł:: Effect of Post Annealing on La$\text{}_{0.7}$Sr$\text{}_{0.3}$MnO$\text{}_{3}$ Thin Films
Autorzy:: Cheng, W. F.
Leung, C. W.
Tematy:: 75.30.-m
73.50.-h; Pokaż więcej
Wydawca:: Polska Akademia Nauk. Instytut Fizyki PAN
Powiązania:: https://bibliotekanauki.pl/articles/2047232.pdf Link otwiera się w nowym oknie
Opis:: The stability of La$\text{}_{0.7}$Sr$\text{}_{0.3}$MnO$\text{}_{3}$ thin films fabricated by pulsed laser deposition, under different annealing procedures, was investigated. La$\text{}_{0.7}$Sr$\text{}_{0.3}$MnO$\text{}_{3}$ films were deposited on (100) LaAlO$\text{}_{3}$ substrates at 650ºC with the films thickness from 20 to 50 nm. The oxygen pressures used to fabricate the films were 150 mTorr and 100 mTorr. Then in situ annealing steps were performed at 100 and 150 mTorr, respectively. Curie temperatures (T$\text{}_{c}$) of the films were estimated from the peaks of the temperature dependent resistance data. For the films deposited at 100 mTorr and annealed at 150 mTorr, T$\text{}_{c}$ slightly dropped for short annealing time and recovered to 360 K for 30 min annealing. For the films deposited at 100 mTorr and annealed at 150 mTorr, it maintained semiconducting behavior without transition after annealing up to 30 minutes. For ex situ post annealing, it was found that the T$\text{}_{c}$ of the films strongly depended on the annealing procedures.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 6.

Tytuł:: A Recommended Integrated Mechanism to Enhance OSH Management of Blue-Collar Foreign Workers in Taiwan
Autorzy:: Liao, H. C.
Cheng, S. F.
Wang, Y.
Lee, L. H.
Tematy:: occupational safety and health
Labor Safety and Health Act
OSH training program
manpower agency
blue-collar foreign worker
bezpieczeństwo i higiena pracy
zdrowie
szkolenie BHP; Pokaż więcej
Wydawca:: Centralny Instytut Ochrony Pracy
Powiązania:: https://bibliotekanauki.pl/articles/90376.pdf Link otwiera się w nowym oknie
Opis:: This study examines the roles and functions of businesses, labor-exporting countries’ representative offices in Taiwan, religious organizations, and manpower agencies in promoting occupational safety and health (OSH). It also offers advice to Taiwanese authorities on making policies and improvements regarding the oversight mechanism mandated by the Labor Safety and Health Act, giving them an idea of what to focus on when enforcing control over blue-collar foreign workers’ OSH conditions. This study also proposes that Taiwanese authorities may serve not only as an overseer/inspector of those hiring blue-collar foreign workers in Taiwan, but also expand their role to lay down policies regarding a variety of OSH teaching materials in the blue-collar foreign workers’ native languages (spoken or written), the qualifications of translators in blue-collar foreign workers’ OSH training programs, and regulations concerning the longer hours such training programs take.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 7.

Tytuł:: System for Calibrating Analogue Merging Units in Absence of Synchronization Signals
Autorzy:: Cheng, H.-M.
Huang, Q.-F.
Ji, F.
Xu, Q.
Liu, J.
Tian, Z.
Tematy:: intelligent substation
analogue merging unit
peer-to-peer communication
calibration system
synchronization signal; Pokaż więcej
Wydawca:: Polska Akademia Nauk. Czytelnia Czasopism PAN
Powiązania:: https://bibliotekanauki.pl/articles/221084.pdf Link otwiera się w nowym oknie
Opis:: Synchronization signals are requisite for calibrating electrical measurement devices with digital output when using conventional calibration methods. However, since the signal sampling process of the analogue merging units (MUs) operating in an intelligent substation does not rely on external synchronization signals, accuracy calibration without the use of synchronization signals is of particular importance in order to guarantee the measurement accuracy in practical situations. So far, very little research on calibration systems independent of synchronization signals has been performed. This paper presents a design of the calibration system without dependence on synchronization signals. To verify the feasibility of the proposed design, the designed system and a conventional calibration system have been employed in testing the accuracy of the same analogue MU of a 0.2 accuracy class. The comparison of the test results shows that the differences of ratio errors are below 0.02%, and the maximum difference of phase errors is about 4′. This paper also provides a new efficient and significant calibration method which does not require any external synchronization signals.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 8.

Tytuł:: Fast and effective extraction for equivalent shunt resistances of triple-junction concentrator solar cells
Autorzy:: Lv, H
Dai, J
Sheng, F
Liu, W
Ma, X
Cheng, C
Lv, Q
Tematy:: concentrator photovoltaic
triple junction solar cell
equivalent shunt resistance; Pokaż więcej
Wydawca:: Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Powiązania:: https://bibliotekanauki.pl/articles/174425.pdf Link otwiera się w nowym oknie
Opis:: Fast and effective extraction of equivalent shunt resistance for each subcell of GaInP/GaInAs/Ge triple-junction concentrator solar cells is presented. The two-diode model of single junction was introduced to establish the equivalent circuit of triple-junction solar cells. The current-voltage characteristic of the triple-junction solar cells was measured under AM1.5D spectrum, C = 576 and T = 303 K. Equivalent shunt resistance of each subcell was extracted from its estimated current-voltage curve. The estimated current-voltage curve of the triple-junction solar cells shows a good agreement with the experimental data in 0.31% deviation. The degradation in the equivalent shunt resistance for Ge subcell was intentionally introduced to indicate the mechanism of current-matching operation for different subcells, with the maximum output power of the triple-junction solar cells deteriorating from 3.5 to 3.17 W. The results can offer performance analysis and optimum design of photovoltaic applications.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 9.

Tytuł:: The Effect of the Energetic Additive Coated MgH2 on the Power of Emulsion Explosives Sensitized by Glass Microballoons
Autorzy:: Cheng, Y.
Wang, Q.
Liu, F.
Ma, H.
Shen, Z.
Guo, Z.
Liu, R.
Tematy:: emulsion explosive
power
hydrogen storage material
magnesium hydride; Pokaż więcej
Wydawca:: Sieć Badawcza Łukasiewicz - Instytut Przemysłu Organicznego
Powiązania:: https://bibliotekanauki.pl/articles/357940.pdf Link otwiera się w nowym oknie
Opis:: Traditional emulsion explosives, in spite of excellent water resistance, safe handling and good storage performance, have low power problems which seriously hinders their use. In order to improve the power of emulsion explosives, a hydrogen based emulsion explosive was devised. Scanning electron microscope pictures and experimental storage results show that the coating effect and stability of coated magnesium hydride (MgH2) are very good. The power of an emulsion explosive sensitized by glass microballoons was significantly increased (24.30 mm compression of lead block) after adding coated MgH2, compared to only 16.10 mm compression when not added. Thus emulsion explosives with coated MgH2 as an energetic additive have many potential applications.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 10.

Tytuł:: Use of nanofiltration membranes to concentrate and recover leached aluminum from acidified water treatment sludge
Autorzy:: Cheng, W. P.
Chen, P. H.
Tian, D. R.
Yu, R. F.
Fu, C. H.
Tematy:: water purification
nanofiltration
acidic solutions
leaching
roztwory kwaśne
oczyszczanie wody
nanofiltracja
ługowanie
glin; Pokaż więcej
Wydawca:: Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Powiązania:: https://bibliotekanauki.pl/articles/208030.pdf Link otwiera się w nowym oknie
Opis:: The recovery of aluminum from water purification sludge is usually performed by making the solution acidic or basic. However, for economic reasons and reasons of safety, excessive doses of acid or base should not be utilized. Accordingly, the aluminum concentration in the leached solution is typically limited, thus the recovered aluminum cannot be directly reused as a coagulant. A nanofiltration (NF) membrane can be used in the acidic solution to concentrate high-valence metal ions. There-fore, in this work, H₂SO₄ was utilized to leach Al³⁺ ions from water purification sludge. Then, the Al³⁺ ion solution was concentrated using a low-price NF membrane. The effect of natural organic matter on the Al³⁺ ion concentrating efficiency in the filtration process has been elucidated. Experimental results reveal that Al³⁺ ions were effectively prevented from passing through the NF membrane, enabling a highly concentrated aluminum solution to be obtained. However, the presence of organic compounds may reduce the efficiency of the concentration of Al³⁺ ions in the solution.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Informacja

Wyszukujesz frazę "Cheng, F." wg kryterium: Autor