Autor: Li, Z.-H. - Prolib Integro

Skocz do pozycji: 1.

Tytuł:: Synergistic effect of a mixture of dodecylamine and kerosene on separation of magnetite ore
Autorzy:: Liu, A.
Fan, M.-Q.
Li, Z.-H.
Tematy:: DDA-kerosene
magnetite ore
quartz
flotation; Pokaż więcej
Wydawca:: Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Powiązania:: https://bibliotekanauki.pl/articles/109849.pdf Link otwiera się w nowym oknie
Opis:: In this study, it was discovered that a mixture of dodecylamine (DDA)-kerosene demonstrated a stronger collecting ability for pure quartz and higher selectivity for magnetite ore. The relationship between the DDA-kerosene composition and mineral flotation performance on reverse flotation of magnetite ore was investigated. The results showed that floatability of the floating material increased when the DDA consumption increased. Specifically, during flotation, the fine particles (-0.074 mm fraction) selectively floated with DDA-kerosene. The difficult to float coarser particles (+0.074 mm fraction) with high content of quartz, required higher DDA dosage. However, higher DDA input during the flotation process did not necessarily yield better outcomes. The best results were obtained for 40/60 amine-to-oil ratio, as the quartz floated markedly with smaller magnetite loss and the flotation behavior was superior to pure DDA. Magnetite concentrates with 1.83% SiO2 and 71.04% Fe were produced using 120 g/Mg of DDA-kerosene (WDDA=40%).
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 2.

Tytuł:: The POLAR gamma-ray burst polarization catalog
Autorzy:: Gauvin, N.
De Angelis, N.
Produit, N.
Tymieniecka, T.
Zhang, S. N.
Kole, M.
Li, H. C.
Rybka, D.
Hajdas, W.
Sun, J. C.
Wu, X.
Burgess, J. M.
Wang, Y. H.
Zhang, Y. J.
Pollo, Agnieszka
Li, Z. H.
Xiong, S. L.
Wu, B. B.
Song, L. M.
Berlato, F.
Greiner, J.
Szabelski, J.
Dostawca treści:: Repozytorium Uniwersytetu Jagiellońskiego

Artykuł

na półce

Skocz do pozycji: 3.

Tytuł:: Calculation of laser radar cross-section of a spatial object and its experimental verification
Autorzy:: Cao, Y.-H.
Wang, Z.
Bai, L.
Wu, Z.
Li, H.-Y.
Li, Y.-H.
Tematy:: bidirectional reflectance distribution function
BRDF
laser radar cross-section
LRCS
spatial object; Pokaż więcej
Wydawca:: Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Powiązania:: https://bibliotekanauki.pl/articles/174167.pdf Link otwiera się w nowym oknie
Opis:: Bidirectional reflectance distribution function of some artificial satellite used materials at the wavelength of 1.06 μm was measured in laboratory. Bidirectional reflectance distribution function (BRDF) models of these materials were established with the five-parameter BRDF model. Laser radar cross-section of a scaled satellite with various materials was calculated, and characteristics of laser radar cross-section of the satellite were discussed. Measurement system to measure laser radar cross-section of the satellite was established and the scaled satellite model was measured. By analyzing the measured data and calculated data, it can be clearly seen that the BRDF of the surface materials and the laser incidence angle are two of main influential factors of the scaled satellite’s laser radar cross-section. These works can provide a reference for design of the lidar system.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 4.

Tytuł:: Reliability modeling of fault tolerant control systems
Autorzy:: Li, H.
Zhao, Q.
Yang, Z.
Tematy:: sterowanie tolerujące uszkodzenia
ocena niezawodności
procesy semimarkowskie
fault tolerant control
reliability evaluation
semi-Markov processes; Pokaż więcej
Wydawca:: Uniwersytet Zielonogórski. Oficyna Wydawnicza
Powiązania:: https://bibliotekanauki.pl/articles/929822.pdf Link otwiera się w nowym oknie
Opis:: This paper proposes a novel approach to reliability evaluation for active Fault Tolerant Control Systems (FTCSs). By introducing a reliability index based on the control performance and hard deadline, a semi-Markov process model is proposed to describe system operation for reliability evaluation. The degraded performance of FTCSs in the presence of imperfect Fault Detection and Isolation (FDI) is reflected by semi-Markov states. The semi-Markov kernel, the key parameter of the process, is determined by four probabilistic parameters based on the Markovian model of FTCSs. Computed from the transition probabilities of the semi-Markov process, the reliability index incorporates control objectives, hard deadline, and the effects of imperfect FDI, a suitable quantitative measure of the overall performance.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 5.

Tytuł:: Nowa metoda analizy drzewa uszkodzeń: rozmyta analiza dynamicznego drzewa uszkodzeń
A new fault tree analysis method: fuzzy dynamic fault tree analysis
Autorzy:: Li, Y. F.
Huang, H. Z.
Liu, Y.
Xiao, N. C.
Li, H.
Tematy:: analiza drzewa uszkodzeń
dynamiczne drzewo uszkodzeń
liczba rozmyta
rozmyty model Markowa
programowanie parametryczne
fault tree analysis (FTA)
dynamic fault tree
fuzzy number
fuzzy Markov model
parametric programming; Pokaż więcej
Wydawca:: Polska Akademia Nauk. Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne PAN
Powiązania:: https://bibliotekanauki.pl/articles/301632.pdf Link otwiera się w nowym oknie
Opis:: Fault tree analysis (FTA) is a widely used reliability assessment tool for large and complex engineering systems. The conventional fault tree analysis method, which contains AND, OR, and Voting gates, etc., can efficiently build an analytical model to represent combinations of component failures that cause the failure of a system. However, due to its limited modeling capability, we may confront difficulties when modeling dynamic systems which involve complicated dynamic characteristics such as sequence dependency and functional dependency. Markov-based dynamic fault tree analysis (DFTA) extends the static FTA by introducing additional gates to model such complicated interactions among events. In many circumstances, it is quite difficult to obtain an accurate system reliability estimate due to limited data. To overcome this issue, a fuzzy dynamic fault tree model is put forth to assess system reliability. To obtain the membership function of the fuzzy probability for the top event of the studied fault trees, the extension principle is employed to calculate the associated membership function via a pair of parametric programming problems. Finally, a case study is presented to demonstrate the application of the proposed approach for the hydraulic system of a CNC machining centre.
Analiza drzewa uszkodzeń (FTA) znajduje szerokie zastosowanie jako narzędzie oceny niezawodności dużych i złożonych systemów inżynierskich. Tradycyjna metoda analizy drzewa uszkodzeń z bramkami logicznymi typu AND, OR, k-z-n, itd. pozwala na sprawne konstruowanie modeli analitycznych reprezentujących kombinacje uszkodzeń elementarnych składowych systemu, które prowadzą do awarii systemu jako całości. Jednakże ograniczone możliwości modelowania jakie daje ta metoda mogą prowadzić do trudności przy modelowaniu systemów dynamicznych posiadających złożone charakterystyki dynamiczne, takie jak zależność sekwencyjna czy zależność funkcjonalna. Analiza dynamicznych drzew uszkodzeń (DFTA) oparta na metodzie Markowa stanowi rozszerzenie tradycyjnej FTA. Wprowadza ona dodatkowe bramki, pozwalając na modelowanie wspomnianych wyżej złożonych interakcji między zdarzeniami. W wielu okolicznościach, ograniczone dane nie pozwalają na otrzymanie dokładnej oceny niezawodności systemu. By rozwiązać ten problem, zaproponowano zastosowanie rozmytego modelu dynamicznego drzewa uszkodzeń do oceny niezawodności systemu. Aby otrzymać funkcję przynależności rozmytego prawdopodobieństwa wystąpienia zdarzenia szczytowego badanego drzewa uszkodzeń, obliczono, na podstawie pary problemów programowania parametrycznego, skojarzoną funkcję przynależności wykorzystując zasadę rozszerzenia. Na zakończenie przedstawiono studium przypadku, w którym proponowane podejście zastosowano do analizy systemu hydraulicznego centrum obróbkowego CNC.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 6.

Tytuł:: Influence of Rolling Friction Coefficient on Inter-Particle Percolation in a Packed Bed by Discrete Element Method
Autorzy:: Zhou, H.
Luo, Z.
Zhang, T.
You, Y.
Li, H.
Zou, Z.
Tematy:: inter-particle percolation
rolling friction coefficient
discrete element method;
percolation velocity
dispersion coefficient; Pokaż więcej
Wydawca:: Polska Akademia Nauk. Czytelnia Czasopism PAN
Powiązania:: https://bibliotekanauki.pl/articles/356261.pdf Link otwiera się w nowym oknie
Opis:: Rolling friction representing the energy dissipation mechanism with the elastic deformation at the contact point could act directly on particle percolation. The present investigation intends to elucidate the influence of rolling friction coefficient on inter-particle percolation in a packed bed by discrete element method (DEM). The results show that the vertical velocity of percolating particles decreases with increasing the rolling friction coefficient. With the increase of rolling friction coefficient, the transverse dispersion coefficient decreases, but the longitudinal dispersion coefficient increases. Packing height has a limited effect on the transverse and longitudinal dispersion coefficient. In addition, with the increase of size ratio of bed particles to percolation ones, the percolation velocity increases. The transverse dispersion coefficient increases with the size ratio before D/d<14. And it would keep constant when the size ratio is greater than 14. The longitudinal dispersion coefficient decreases when the size ratio increases up to D/d=14, then increases with the increase of the size ratio. External forces affect the percolation behaviours. Increasing the magnitude of the upward force (e.g. from a gas stream) reduces the percolation velocity, and decreases the dispersion coefficient.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 7.

Tytuł:: Dft investigation of a high energy density polynitro compound, 2,2’-Bis(trinitromethyl)-5,5’-azo-1,2,3,4- tetrazole
Autorzy:: Lin, H.
Zhu, S. G.
Chen, P. Y.
Li, K.
Li, H. Z.
Peng, X. H.
Tematy:: polynitro
electronic structure
thermodynamic properties
crystal structure
detonation performance
stability; Pokaż więcej
Wydawca:: Sieć Badawcza Łukasiewicz - Instytut Przemysłu Organicznego
Powiązania:: https://bibliotekanauki.pl/articles/358030.pdf Link otwiera się w nowym oknie
Opis:: A novel polynitro compound, 2,2’-bis(trinitromethyl)-5,5’-azo- 1,2,3,4-tetrazole, was designed and investigated at the DFT-B3LYP/6-31G(d) level. Its properties, such as electronic structure, IR spectrum, heat of formation, thermodynamic properties and crystal structure, were predicted. This compound is most likely to crystallize in the P21 space group, and the corresponding cell parameters are Z = 2, a = 5.46 Å, b = 9.72 Å, c = 14.05 Å, α = 90°, β = 90°, γ = 90°. In addition, the detonation velocity and pressure were also estimated by using the empirical Kamlet-Jacobs equations, and were predicted to be 8.28 km/s and 31.61 GPa respectively. The oxygen balance of this compound is +13.79%, which indicates that it could serve as an oxidizer. Bond dissociation energy calculations show that the C(13)-N(21)O2 and C(14)-N(30)O2 bonds are the locations of thermal decomposition and that this compounds meets the thermal stability requirements as an exploitable explosive. Keywords: polynitro, electronic structure, thermodynamic properties, crystal structure, detonation performance, stability.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 8.

Tytuł:: Simulation of irregular waves in a numerical wave tank
Autorzy:: Li, Z-F.
Shi, Y. Y.
Ren, H. L.
Li, H.
Ashraf, M. A.
Tematy:: open boundary condition
multi transmitting formula
irregular waves
boundary element method
numerical wave tank; Pokaż więcej
Wydawca:: Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Powiązania:: https://bibliotekanauki.pl/articles/260392.pdf Link otwiera się w nowym oknie
Opis:: The time domain boundary element method was utilized to simulate the propagation of the irregular waves in a numerical wave tank. The problem was solved in a time-marching scheme, upon the irregular waves being fed through the inflow boundary, in which the theoretical solution was obtained from the wave energy spectrum. The open boundary condition was modeled by the multi transmitting formula (MTF), in which the phase velocity was calculated according to the Sommerfeld’s condition. The velocity potential and wave elevation were directly obtained by integrating the free surface condition twice, with respect to time. The accuracy of the developed numerical scheme was verified by simulating the propagation of irregular waves. The numerical results show good agreements with the analytical solutions, which prove that the proposed scheme is a promising way to the simulation of wave-body interactions.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 9.

Tytuł:: An efficient algorithm for estimating the parameters of superimposed exponential signals in multiplicative and additive noise
Autorzy:: Bian, J.
Peng, H.
Xing, J.
Liu, Z.
Li, H.
Tematy:: superimposed exponential signals
modified Newton–Raphson algorithm
multiplicative noise
additive noise
least squares estimator
algorytm Newtona-Raphsona
metoda najmniejszych kwadratów
estymator; Pokaż więcej
Wydawca:: Uniwersytet Zielonogórski. Oficyna Wydawnicza
Powiązania:: https://bibliotekanauki.pl/articles/331007.pdf Link otwiera się w nowym oknie
Opis:: This paper considers parameter estimation of superimposed exponential signals in multiplicative and additive noise which are all independent and identically distributed. A modified Newton–Raphson algorithm is used to estimate the frequencies of the considered model, which is further used to estimate other linear parameters. It is proved that the modified Newton–Raphson algorithm is robust and the corresponding estimators of frequencies attain the same convergence rate with Least Squares Estimators (LSEs) under the same noise conditions, but it outperforms LSEs in terms of the mean squared errors. Finally, the effectiveness of the algorithm is verified by some numerical experiments.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 10.

Tytuł:: Nonlinear drift of the spring gravimeter caused by air pressure from the kunming GS15 gravimeters
Autorzy:: Wei, J.
Shen, W.
Li, H.
Liu, Z.
Tematy:: GS15 gravimeter meter
air pressure admittance
nonlinear air pressure correction
superconducting gravimeter; Pokaż więcej
Wydawca:: Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Powiązania:: https://bibliotekanauki.pl/articles/260586.pdf Link otwiera się w nowym oknie
Opis:: In order to monitor and correct the meteorological factors of the spring gravity meter, the characteristics of the time varying gravity changes caused by meteorological factors were analyzed. Kunming GS15 gravity meter from 2007 continuous gravity observation has been carried out with the sampling rate of the pressure observation. In this study, we first compare the effects of 4 types of gravity meter and 3 different types of stations on the gravity observed seasonal gravity signals. It is indicated that the observed seasonal gravity signal of the cave is only 1/10, and there is a constant temperature and constant pressure device. Compared with the same time, the gravity signal of the gravity signal is about 100 times smaller. The influence of the pressure load of the gravity meter is tested by using the theory of pressure. The results show that only the actual value of 2cpd - 3cpd pressure load varies from -0.395 to -0.280×10-8ms-2 , and the 1cpd to 1 cpm periodic partial type gravity meter is also in accordance with the law of gravity and air pressure. And with the characteristics of time lag. In this paper, the nonlinear zero drift parameters of the linear regression model with time lag and the time series of the GS15 gravity meter are used to simulate the nonlinear zero drift parameters of the gravity meter. The results show that the gravity signal contains time lag 35 hours, and the air pressure admittance is 0.8 × 10-8ms-2/mbar. The correlation can reach 79%. The gravity changes signal and satellite gravity as well as the gravity water load signal of the land water model are the same as the gravity water load signal in the autumn as the minimum value, and the seasonal variation of the maximum value of gravity in summer.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Informacja

Wyszukujesz frazę "Li, Z.-H." wg kryterium: Autor