Temat: austenitizing temperature

Skocz do pozycji: 1.

Tytuł:: Eutectoid Reaction Ar1 of Cast Iron GJS-400-15 in Isothermal Conditions
Autorzy:: Szykowny, T.
Romanowski, Ł.
Giętka, T.
Tematy:: heat treatment
spheroidal cast iron
eutectoid reaction
austenitizing temperature
kinetics of eutectoid reaction
obróbka cieplna
żeliwo sferoidalne
reakcja eutektoidalna; Pokaż więcej
Wydawca:: Polska Akademia Nauk. Czytelnia Czasopism PAN
Powiązania:: https://bibliotekanauki.pl/articles/381418.pdf Link otwiera się w nowym oknie
Opis:: This scientific paper presents the research on influence of austenitizing temperature on kinetics and evolution of the spheroidal plain cast iron during eutectoid reaction in isothermal conditions. The cast iron has been austenitized in temperatures of 900, 960 or 1020°C. Therewere two temperature values of isothermal holding taken into consideration: 760 or 820°C. The order of creation of reaction products and their morphology have been analyzed. The particular attention has been paid to the initial stage of transformation. The qualitative research has been executed using the transmission electron microscope (TEM), as well as quantitative research (LM). The influence of austenitizing temperature has also been determined on transformation kinetics and structural composition. It was found that the increase of austenitizing temperature is conductive to the initial release of structures by metastable system. A reduction of time was observed of the initial stage of transformation at temperature close to Ar12 with its simultaneous elongation at temperature close to Ar11, with an increase of austenitizing temperature. The dependences obtained by the metallographic method confirm the prior results of dilatometric research of eutectoid reaction.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 2.

Tytuł:: Effect of high-temperature heating on chemical changes in M7C3 carbides of AISI D2 tool steel
Autorzy:: Nykiel, T.
Hryniewicz, T.
Tematy:: D2 tool steel
high-temperature heating
Austenitizing
coarse primary M7C3 carbides
chemical composition; Pokaż więcej
Wydawca:: Przedsiębiorstwo Wydawnictw Naukowych Darwin / Scientific Publishing House DARWIN
Powiązania:: https://bibliotekanauki.pl/articles/411883.pdf Link otwiera się w nowym oknie
Opis:: The paper presents the study results obtained on 16H12MF/NC11LV/D2 tool steel. The main purpose of the study was to establish the chemical composition of the coarse primary M7C3 carbides occurring in that steel after a standard soft annealing. The effect of high-temperature annealing in the air atmosphere was investigated. The study was limited to the decarburized layer, on the distance of about 0.4 mm from the surface, of hardened steel after annealing and austenitizing at 1150 ºC in the air atmosphere for the periods of 30 and 90 minutes. It was found that the coarse primary M7C3 carbides of the annealed D2 tool steel differ significantly as to the contents of Cr, Mo, and V, and in the most degree to the contents of chromium and molybdenum. The average concentration of chromium rises successively with the growth of austenitizing time. On the other hand, the concentrations of molybdenum and vanadium are lower after 30 minutes of austenitizing than their concentrations in the similar carbides of the annealed steel. Prolongation of the austenitizing time up to 90 minutes results in the increase of molybdenum and vanadium contents in the coarse carbides. It was found that austenitizing of AISI D2 tool steel at the temperature of 1150 ºC in the air atmosphere leads to precipitation of the second phase, brighter in the BSE_Z pictures, in relation to the matrix of carbides, with the amount and magnitude being higher with the annealing time.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Informacja

Wyszukujesz frazę "austenitizing temperature" wg kryterium: Temat