Temat: emissivity - Prolib Integro

Skocz do pozycji: 1.

Tytuł:: Device for emissivity estimation in LWIR range
Autorzy:: Olbrycht, R.
Tematy:: emissivity
infrared
thermal camera; Pokaż więcej
Wydawca:: Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Powiązania:: https://bibliotekanauki.pl/articles/114198.pdf Link otwiera się w nowym oknie
Opis:: The paper deals with the influence of emissivity on infrared measurements (Tab. 1; Fig. 1-3) and presents the developed device for emissivity estimation (Fig. 4). There is comparison shown between the reference emissivity values measured with thermal camera (Fig. 5) and estimated with the developed device (Tab. 2). Obtained results are in good agreement for three examined samples with emissivity ranging from 0.1 to 0.95.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 2.

Tytuł:: Work on developing a thermal shooting target
Autorzy:: Swiderski, W.
Hłosta, P.
Polak, G.
Tymiński, D.
Tematy:: thermal target
infrared
emissivity
shooting; Pokaż więcej
Wydawca:: Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Powiązania:: https://bibliotekanauki.pl/articles/114252.pdf Link otwiera się w nowym oknie
Opis:: The paper presents work on the development of a thermal target providing for shooting with the use of night-vision and thermovision sights in night conditions as well as during the day, without changing the target. The image of the target in the night sight is visible by illuminating it through an IR lamp. The target is designed so that the reflected IR stream is directed towards the objective lens. Compared to existing solutions, the new thermal target has a number of advantages, such as it does not require long-time heating and is immediately ready to operate after thermal lamp lighting, significantly reducing energy consumption. The project is currently at the stage of prototype target testing.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 3.

Tytuł:: Testing coatings of reflecting infrared radiation for a target for night shooting
Autorzy:: Swiderski, Waldemar
Hłosta, Paweł
Polak, Grzegorz
Tymiński, Dariusz
Tematy:: thermal target
infrared
emissivity
shooting; Pokaż więcej
Wydawca:: Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Powiązania:: https://bibliotekanauki.pl/articles/114598.pdf Link otwiera się w nowym oknie
Opis:: The paper presents the principle of operation of a new night-shooting target. Because this target requires a covering that reflects the infrared radiation flux generated by the reflector from its surface, testing of different variants of the cover and the shape of the target surface has been carried out. Emissivity is a physical parameter characterizing the radiant properties of real bodies. The emissivity coefficient of extruded aluminum sheet samples covered with a layer of green colored aluminum oxide was determined. The aluminum oxide layer was applied using two different technologies being galvanic and anodizing.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 4.

Tytuł:: Compatibility of the λ- Kolmogorov test for the brake disc emissivity factor distribution in thermal imaging studies
Autorzy:: Sawczuk, W.
Pagórek, B.
Tematy:: emissivity factor
brake disc
exponential distribution; Pokaż więcej
Wydawca:: Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Powiązania:: https://bibliotekanauki.pl/articles/114266.pdf Link otwiera się w nowym oknie
Opis:: A thermal imaging camera is widely used in railway, it allows evaluating the wheel-rail contact while rolling the wheel set on the rails [3], cracks of the railway tracks [22] or identify overheated axle bearings of the wheel sets of the railway cars. In studies of braking systems both railway and vehicular ones on brake positions, the thermal imaging measurements are little used. Only in the qualitative assessment, an IR camera can identify the phenomenon of "hot spots" on the brake disc [1, 12, 15]. When testing the disc brake friction pairs, the most difficult is the brake disc and determination of its actual temperature which, due to the polished smooth surface by friction with the friction pad, is a low-carbon object. This type of objects force the person who makes the measurements to do a very precise configuration of the thermal imaging camera in order to determine the emissivity factor. An additional difficulty in the thermal imaging of braking systems is a dynamically changeable nature of the work associated with changes in the rotational speed of the brake disc and a nonlinear increase in its temperature. The paper presents the results of the studies conducted parallel with the thermal imaging measurements by using thermocouples to determine variability of the experimental emissivity factor of the brake disc supported by the λ-Kolmogorov compatibility test.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 5.

Tytuł:: Study of selected physical, chemical and biological properties of selected materials intended for contact with human body
Autorzy:: Mrówka, Maciej
Machoczek, Tomasz
Jureczko, Paweł
Szymiczek, Małgorzata
Skonieczna, Magdalena
Marcoll, Łukasz
Tematy:: absorption
hardness
biocompatibility
structural materials
emissivity; Pokaż więcej
Wydawca:: Zachodniopomorski Uniwersytet Technologiczny w Szczecinie. Wydawnictwo Uczelniane ZUT w Szczecinie
Powiązania:: https://bibliotekanauki.pl/articles/778721.pdf Link otwiera się w nowym oknie
Opis:: The purpose of the conducted study was to analyse new materials intended for contact with the human body in view of their physical, chemical and biological properties. The authors have put to test six commercially available materials, four out of which were composite polyamide 12-based materials, while two were polyurethanes. The examined materials were assessed in terms of the surface. Subsequently, their hardness and biocompatibility were tested. The authors devoted major attention to the tests of absorption and emissivity of water, the pH = 7.4 PBS buffer solution and pH = 4.3 artificial sweat in temperatures of 21°C and 37°C. The results of the tests have confirmed the non-toxicity of all the tested materials and allowed to provide their characteristics in terms of their surface, hardness, as well as absorption and emissivity of various body fluids. Both polyamide 12 and the tested polyurethanes are classified as thermoplastics that may be used in additive technology.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 6.

Tytuł:: Appointing of surface topography parameters to describe the diffuse reflective properties of selected dielectrics
Autorzy:: Majchrowski, R.
Rozanski, L.
Grochalski, K.
Tematy:: thermographic measurements
surface topography
emissivity
reflection; Pokaż więcej
Wydawca:: Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Powiązania:: https://bibliotekanauki.pl/articles/114434.pdf Link otwiera się w nowym oknie
Opis:: The investigations have been performed in order to choose the specific roughness parameters, which would inform the customer about the diffuse emissive and reflective characteristics of the adhesive tapes used in the thermographic measurements. To achieve that, a series of the surface topography parameters of various adhesive tapes (i.e. objects with diffusive reflective characteristics) and various glass plates (i.e. objects with directional reflective characteristics) has been examined. For the analysis of surface topography the following parameters were selected: Sdr (the Developed Interfacial Area Ratio) and Sdq (the Root Mean Square Surface Slope). These selected parameters seem to be most suitable to describe the properties of the surface in the discussed aspect.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 7.

Tytuł:: Badania emisyjności żużla stalowniczego w zakresie podczerwieni MWIR i LWIR
Steel slag emissivity research in MWIR and LWIR infrared ranges
Autorzy:: Więcek, B.
Świątczak, T.
Olbrycht, R.
Wittchen, W.
Borecki, M.
Tematy:: termowizja
żużel
emisyjność
thermovision
slag
emissivity; Pokaż więcej
Wydawca:: Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Powiązania:: https://bibliotekanauki.pl/articles/157655.pdf Link otwiera się w nowym oknie
Opis:: W pracy przedstawiono wstępne badania emisyjności żużla stalowniczego w dwóch zakresach widmowych podczerwieni MWIR i LWIR. Wyniki wykazały znaczące różnice emisyjności spektralnej, co można wykorzystać do określenia parametrów żużla stalowniczego. Ideą prowadzonych badań jest poszukiwanie nowych zastosowań termowizji w metalurgii stali.
In this work, the preliminary results of emissivity for steel slag measured in two spectral ranges, MWIR and LWIR are presented. The investigations confirmed significant difference of spectral emissivity. The results can be used for estimation of technological parameters in the steel slag. The idea of the investigations presented in this paper can be useful in searching new applications of the thermovision in ferrous metallurgy.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 8.

Tytuł:: Pomiary emisyjności powierzchni zewnętrznych kadzi stalowniczych z wykorzystaniem kamery termowizyjnej
External measurements of the surface emissivity of steel ladles with using thermal imaging camera
Autorzy:: Hutny, A. M.
Wyczółkowski, R.
Warzecha, M.
Tematy:: kadź stalownicza
emisyjność
termowizja
ladle
emissivity
thermovision; Pokaż więcej
Wydawca:: Sieć Badawcza Łukasiewicz - Instytut Metalurgii Żelaza im. Stanisława Staszica
Powiązania:: https://bibliotekanauki.pl/articles/182481.pdf Link otwiera się w nowym oknie
Opis:: W artykule przedstawiono badania poświęcone pomiarom emisyjności kadzi stalowniczych. Uzyskano dane dotyczące temperatur w wybranych punktach powierzchni płaszcza analizowanych kadzi, pochodzących z pomiaru stykowego. Dla każdej kadzi zarejestrowano termogramy. Wykazano, że wartość badanego parametru zależy istotnie od stopnia pokrycia kadzi zanieczyszczeniami. Ustalono, że emisyjność powierzchni zewnętrznych badanych kadzi stalowniczych mieści się w zakresie od 0,75 do 0,92.
The article presents research performed to obtain the emission coefficient of the investigated steel ladles. The measurements were perfomed for selected points in the mantle surface of the analyzed ladle with the direct contact measurement. Thermal images were recorded for different ladles. It has been shown that the value of the examined parameter significantly depends on the degree of coverage of the ladle impurities. It was found that the emissivity of the outer surfaces of the tested steel ladles are in the range from 0.75 to 0.92.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 9.

Tytuł:: Emissivity measurement of black paint using the calorimetric method
Autorzy:: Pelińska-Olko, Ewa
Tematy:: calorimetric method
emissivity
thermosensitive materials
polymers
plastics; Pokaż więcej
Wydawca:: Polska Akademia Nauk. Czasopisma i Monografie PAN
Powiązania:: https://bibliotekanauki.pl/articles/27312234.pdf Link otwiera się w nowym oknie
Opis:: The paper is of practical importance and describes the construction of a test rig and the measurement method for determining the relative emissivity coefficient of thermosensitive thin polymer coatings. Polymers are high-molecular chemical compounds that produce chains of repeating elements called ‘mers’. The polymers can be natural and artificial. The former ones form the building material for living organisms, the latter – for plastics. In this work, the words plastics and polymers are used as synonyms. Some plastics are thermosensitive materials with specific physical and chemical properties. The calorimetric method mentioned in the title consists of two steps. The first stage, described here, involves very accurately measuring the emissivity of black paint with the highest possible relative emissivity coefficient, which covers the surface of the heater and the inner surface of the chamber. In the second step, the thermosensitive polymer will be placed on the inner surface of the chamber, while black paint with a known emissivity coefficient will remain on the heater. Such a way of determining the properties of thermosensitive polymers will increase the error of the method itself, but at the same time will avoid melting of the polymer coating. During the tests, the results of which are presented in this work, the emissivity coefficient of the black paint was obtained in the range of 0.958–0.965.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Skocz do pozycji: 10.

Tytuł:: Analiza czynników składowych błędów pirometrii radiacyjnej
Analysis of component factors of radiative pirometry errors
Autorzy:: Hots, N.
Piątkowski, T.
Tematy:: pomiary temperatury
pirometry
emisyjność
temperature measurements
pyrometers
emissivity; Pokaż więcej
Wydawca:: Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Powiązania:: https://bibliotekanauki.pl/articles/157685.pdf Link otwiera się w nowym oknie
Opis:: W artykule zamieszczono analizę źródeł błędów pomiaru temperatury w jednopasmowej pirometrii radiacyjnej w zakresie temperatur od 0°C do 500°C. Wykonano pomiary zmian emisyjności w funkcji temperatury dla utlenionej stali z pieca cementowego oraz stopu aluminium. Przedstawio-no algorytm obliczeń błędu pomiarowego w pirometrze. Wyznaczono za jego pomocą wpływ takich czynników jak błąd określenia emisyjności, wpływ promieniowania tła oraz emisyjność zmienną z temperaturą obiektu.
The paper describes error sources in non-contact, single band pyrometer temperature measurements within the range 0-500°C. The main causes of measurement errors are summarized in Table1. The relation between the emissivity and temperature was measured for the oxidized steel interior of cement kiln and aluminum alloy. The measurement results are shown in Fig. 2. The algorithm of calibration procedure and approximation of the calibration curve are presented. The errors introduced by calibration (Fig. 3.) and the method for error estimation in a virtual pyrometer are given. The influence of physical parameters of the measured object and its surrounding on the radiative temperature measurement accuracy is discussed. The mentioned algorithm was also used to determine the influence of such factors as the emissivity assessment error (Fig. 4) and the error caused by temperature dependence of the object emissivity (Fig. 5). The magnitude of measurement error resulting from reflected background temperature was also determined (Fig. 6). The methods for diminishing the effect of the considered factors on the result of radiative temperature measurements are proposed.
Dostawca treści:: Biblioteka Nauki

Artykuł

na półce

Informacja

Wyszukujesz frazę "emissivity" wg kryterium: Temat